Fire-Safe Valves: API 607, API 6FA and ISO 10497 Compared
A fire-safe certificate is one of the few documents in a valve order that describes a valve failing on purpose. The valve is burned, then pressure-tested while still hot and afterwards when cooled - and it has to keep its leakage within limits and remain operable. That is what the certificate proves, and it is a narrower claim than most people assume.
What the test does to the valve
The sequence set out in the fire-test standards is deliberately brutal:
- The valve, in the closed position, is mounted in a test rig with the cavity and one side pressurised.
- It is exposed to a flame for a defined period - typically 30 minutes - with temperatures measured at several points on the body, aiming at 750 °C to 1,000 °C at the hottest.
- While still hot, the valve is pressure-tested. External leakage past the body joints and the stem seal is measured, and internal leakage past the closure is measured.
- The valve is cooled and tested again.
- The valve must then still be operable - by hand, by gear, or by its actuator, depending on the standard.
The soft seats, seals and packings are usually destroyed. The point of the test is not that the valve survives intact - it is that the pressure boundary and the stem seal do not fail catastrophically and that isolation is degraded rather than lost.
The three standards you will see
| Standard | Applies to | Notes |
|---|---|---|
| API 607 | Quarter-turn valves (ball, butterfly, plug) with soft or non-metallic seats | The most commonly quoted fire test in oil and gas procurement |
| API 6FA | Valves to API 6A and API 6D - including gate, ball, and check valves for pipeline and wellhead service | Written for the valve types covered by those product standards |
| ISO 10497 | Valves generally - the international fire type-test | Technically equivalent in intent to API 607; accepted where ISO is the governing standard |
API 6FD covers the fire testing of check valves. A certificate quoting only "fire-safe" without a standard, a test laboratory and a valve model has told you nothing you can verify.
What the certificate should show
- The standard and its edition (API 607 6th edition, ISO 10497:2010, and so on).
- The testing laboratory - and whether it is accredited for that test.
- The valve covered: manufacturer, model or type, size range, pressure class, seat and seal materials, and the design standard.
- Test parameters: duration, measured temperatures, test pressures.
- Results: external leakage, internal leakage, and the operability check, with actual numbers.
- The date of test and the report reference.
Note the coverage clause. A certificate for one size and one seat material does not automatically cover a different bore, a different class, or metal seats instead of PTFE. When a project requires fire-safe certification for a specific valve, the certificate should name that valve - or the vendor should be able to show that the tested article is representative under the standard's extrapolation rules.
Fire-safe is not fireproof
This is the misunderstanding that causes trouble in reviews.
| Fire-safe means | Fire-safe does not mean |
|---|---|
| After a defined burn, leakage stayed within the standard's limits | The valve will be reusable after a fire - it will not |
| The pressure boundary did not rupture during the test | The valve is suitable for continuous high-temperature service |
| The stem seal leakage was limited | The actuator, solenoid or cabling survived - those are separate items |
| The valve could still be operated after the burn | The valve meets a SIL or functional-safety requirement - that is IEC 61508/61511 |
An ESD valve in a fire zone needs fire-safe certification and an actuator that fails in the safe direction and cabling that survives long enough to do it. The certificate covers one part of that chain.
When to require it, and when to question it
| Situation | Reasonable requirement |
|---|---|
| Hydrocarbon service inside a plant, within a fire zone | Fire-safe per API 607 or ISO 10497, certificate supplied |
| Pipeline stations and terminals | Fire-safe per API 6FA or API 607 depending on valve type |
| Utility water, air, instrument lines outside fire zones | Usually unnecessary - do not pay for it |
| Wellhead and high-pressure service | Per API 6A/6FA, as the operator specifies |
| Hydrogen and oxygen service | Fire-safe plus process-specific requirements; the fire test alone does not qualify the valve |
If a quotation charges a premium for "fire-safe design" but cannot produce a test report naming the model, treat the premium as unverified. Certification is a test result, not a design intention.
Related reading
- Materials and NACE MR0175 for sour service - the other material-side requirement that usually travels with fire-safe.
- Pressure testing: shell and seat tests - the routine production test, which is a different and much simpler claim.
- EN 10204 3.1 vs 3.2 certificates - how the certificate chain fits together.
- DBB vs DIB vs single block - the arrangement decision that precedes the certification question.
Need a fire-safe certificate checked against a specification?
Send the valve datasheet and the requirement the project is quoting. We will confirm whether the certificate on offer actually covers the article, the size and the seat material - before the valves are built.
Request a quote: contact form or websale@sawye.com